UNIQUELY DESIGNED INSERTS FOR HIGH VERSATILITY, ECONOMY AND PRODUCTIVITY Front Turning, Back Turning, Profiling, and Face Turning with ONE SINGLE TOOL ATXOR/L: STXCR/L-CHP-MC: 6C-TOMG-TM: 6V-TOMG-TSF: Double-clamp toolholder with 95 and 117.5 deg approach angle, for negative 80 and 35 deg triangular inserts Screw-on toolholder with coolant holes and with 105 deg approach angle, for positive triangular inserts Negative relief ang., M class 80 deg corner angle insert for “AddMultiTurn”, for medium cutting Negative relief ang., M class 35 deg corner angle insert for “AddMultiTurn”, for finishing PART # RE IC S D1 Tough ◄———————► Hard Grade 6C-TOMG250608M-TM .0315 .476 .250 .203 AH8015 T9215 T9225 6C-TOMG250612M-TM .0472 .476 .250 .203 AH8015 T9215 T9225 PART # RE IC S D1 Tough ◄———————► Hard Grade 6V-TOMG250604F-TSF .0157 .500 .250 .203 AH8015 T9215 T9225 6V-TOMG250608F-TSF .0315 .500 .250 .203 AH8015 T9215 T9225 PART # H B LF LH HF WF RE INSERTS 80° 35° ATXOR/L128-A 0.750 0.750 4.500 1.260 0.750 1.000 .0310 6C-TOMG2506... 6V-TOMG25006... ATXOR/L168-A 1.000 1.000 6.000 1.260 1.000 1.250 .0310 6C-TOMG2506... 6V-TOMG25006... ATXOR/L208-A 1.250 1.250 7.000 1.260 1.250 1.500 .0310 6C-TOMG2506... 6V-TOMG25006... Right hand (R) shown 80° CORNER 35° CORNER Please note, when machining with pull face-turning method, that 6C-TOMG2506... insert may interfere with the workpiece whose external diameter is 1.181 inch or smaller. Please note that 3C-TCMT... insert is not recommended for pull face-turning method (pulling the insert away from the part center). Please note, when machining with pull face-turning method, that 6V-TOMG2506... insert may interfere with the workpiece whose external diameter is 2.756 inch or smaller. 3C-TCMT 3 corners (positive insert) 60 degrees WITH COOLANT HOLES→ 3C-TCMT-TM: PART#: B H LF WF HF LH L5 INSERT STXCR/L169-CHP-MC 1 1 6 1.1/4 1 1.1/4 1.38 3C-TCMT29X608-TM STXCR/L2525X29-CHP-MC 25 25 122 32 25 32 35 TOOLHOLDERS INSERTS Positive 7 deg relief angle, M class, triangular insert with Y-PRISM’s safe lock design. PART # RE IC S D1 Grade 3C-TCMT29X608TM .0315 .630 .242 .217 T9215 CARBIDE GRADES WILL ACCEPT 2 INSERT STYLES For 6C** inserts For 6V** inserts - 796 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042 P M K ● P10 − P20 ● Well balanced between wear and chipping resistance ● First choice for steel ● High versatility for a wide range of applications A9215 FOR: STEEL, STAINLESS AND CAST IRON P M K S H ● M01 − M20 / S10 − S20 ● Good balance between wear and fracture resistance ● First choice for machining heat-resistant alloy under general cutting conditions AH8015 FOR: STAINLESS, HIGH-TEMP, STEEL & CAST IRON P ● P15 − P25 ● First choice for roughing to medium cutting ● High fracture resistance T9225 FOR: STEEL
