BRIGHT LIGHT FOR A DARK MACHINE WITH CHIP-SHIELD™ PROTECTED AGAINST HOT FLYING CHIPS AND CUTTING FLUIDS SUPER ABSORBENT PADS * Pad count is approximate ● Laminated for maximum strength ● Grime-hiding gray color ● Pure meltblown polypropylene fibers are the most cost-effective absorption technology today ● These durable, medium-weight pads absorb all types of liquids ● Ideal when you have to clean up general spills or drips ● Great for tough spill situations Note: This unit is supplied with pipes to fit all 3 of the most popular containers: 5 GAL. buckets, 55 GAL. drums and totes*. ● Ends emulsion guesswork ● Reduces waste ● No more hand batching ● Saves time, money and space ● Perfectly mixed coolant for your machine ● Keep drums upright ● Check valve insures proper mix- ture instantly ● Locknut on dial discourages tampering ● Locknut with padlock available ● Separate water shut-off valve ● Machined from solid bronze casting ● No moving parts ● Steel stand pipe Premium Mixer fits 5 GAL., 55 GAL. & Totes* MACHINIST’S PREMIUM MIXER Consistent Results, Last Forever Fits: 5 GAL. Buckets, 55 GAL. Drums and Totes DISK SKIMMERS ● Maximizes coolant performance ● Extends coolant life ● Available in different sizes ● Special high-temp disks for parts washers (LW style) LH300 shown H series Disks are rated up to 90°F (32°C). W Series Disks are rated up to 212°F (100°C). *CSA and CE approved units are available - call for a quote. * NOTE: ADAPTER REQUIRED TO FIT TOTE - PART# 1-ZEB-MIX03TOTE330 The Keller Pump/Filter Unit PFA-1002 filters sludge and chips from waterbase machine tool coolant or from cutting oil in sumps, without the need to pump out the sumps. With a recirculation rate of 20 gallons per minute, the PFA-1002 completely cleans settled sludge and suspended solids from a typical sump (from 15 gallons to about 250 gallons) in minutes, and then can easily be moved to another sump and set up to run, simply by connecting a 1/4-inch compressed air line. Each PFA- 1002 is supplied complete with a rugged, air-operated diaphragm pump, a high capacity bag filter, * 25 micron filter bags supplied unless otherwise specified Other efficiencies available: 100, 50, 10, 5 micron Compressed air flow requirement- 5 SCFM Compressed air inlet fitting- 1/4” NPTF Shop compressed air pressure- 20 psig to 100 psig Shipping Weight (Shipped by UPS)- 100 lbs KELLER PORTABLE PUMP/FILTER UNIT Filter Chips & Sludge Without Pumping out Sumps DESCRIPTION PART # Pump/Filter Unit, with 5 Filter Bags 1-KEL-PFA-1002* Replacement Filter Bags, Box of 5 Bags 1-KEL-RCP-25* and all required inlet and outlet hoses, mounted on a compact (30”x 20”) cart. The filter/ regulator for compressed air is provided. Five 25 micron filter bags are provided as standard. Other filter bags from 5 microns to 100 microns are available. ● Unbreakable disk (lifetime guarantee) ● Wipers that don’t need adjustment (lifetime guarantee) ● Surge-protected motor with one year warranty ● Rated up to 5 gallons per hour VAC-U-GUN™ BLOW GUN, VACUUM & TRANSFER WITH NO MOVING PARTS In seconds, the Vac-u-Gun can be transformed from a powerful vacuum gun into an efficient blow gun or into a transfer tool for lightweight materials. PART # 1-EXA-6392 Two-Way Pumping With the turn of a knob, EXAIR’s Model 6196 Reversible Drum Vac System will quickly fill or empty a 55 gallon (40 imperial gallon) drum. Coolant sumps can be easily refilled, or contaminated liquids transferred to filtration tanks in minutes. The flow rate in and out of the drum can be controlled with the knob, making it ideal for dispensing liquids. No moving parts or electricity assures Model 6196 Reversible Drum Vac fills or empties machine sumps quickly and easily. ALL STAINLESS STEEL PUMP! NO BRASS OR ALUMINUM! Model 6901 Spill Recovery Kit used with the Drum Vac provides fast cleanup of messy spills. DRUM-VAC™ FILL 55 GALLON DRUM IN 90 SECONDS Accessories PART # DESCRIPTION 1-EXA-6901 Spill Recovery Kit includes a one-piece 54” (1.4m) ABS wand and 14” (36cm) double blade squeegee tool. 1-EXA-6569 10’ 1.1/2” flexible vaccum hose w/ cuffs 1-EXA-6569-20 20’ 1.1/2” flexible vaccum hose w/ cuffs Drum Vac Systems PART # DESCRIPTION 1-EXA-6196 Reversible Drum Vac System - includes two-way pump assembly (1/4 NPT), shutoff valve, 10’ (3m) flexible vacuum hose (1.1/2”/38mm I.D.) with 90° quick release elbow connection, (1) aluminum wand (drum not included). CHIP-VAC™ VACUUMS CHIPS DIRECTLY INTO A 55 GALLON DRUM - WITH NO MOVING PARTS Chip Vac is used to clean chips from fixtures, floors and work surfaces of machining centers, lathes, saws, mills and other industrial equipment. Dusty materials such as absorbents are trapped by the 0.1 micron filter bag to keep the surrounding air clean. PART # 1-EXA-6193 • 120V - 6 Hz • 25’ CORD ● “O” rings inside the lighthead protect the electrical components from liquids and dust. STANDARD 36 WATT LIGHTS MOUNTING GRIPS FOR MACHINE LIGHTS TYPE PART # Machine Bracket Mount SL-5000-1088 Magnetic Mount - 82# SL-5000-1077 Magnetic Mount - 110# SL-5000-1078 PART # LIGHTHEAD LGTH DIA. SL-1636-2014 25” 3” maintenance free operation. An automatic safety shutoff valve prevents spills or overfilling. ITEM SIZE QUANTITY * PART # PADS 15" x 17" 100/cs 6-666-660 MODEL P/N: 1-ZEB- MIXING RANGE % GALLONS/ MINUTE MAX. RATIO NPT FITTING IN SIZE OUT MIXU03725 0-25 3 3:1 3/8” 1/2” DESCRIPTION P/N: 1-ZEB- 12” w/7 rpm regular motor* LH300 18” w/7 rpm regular motor* LH460 24” w/2 rpm fan-cooled motor* LH610 12” w/7 rpm fan-cooled motor, high temp disk, stainless steel collar LW300 18” w/7 rpm fan-cooled motor, high-temp disk, stainless steel collar LW460 24” w/2 rpm fan-cooled motor, high-temp disk, stainless steel collar LW610 - 1875 - Toll Free Fax Email Houston Bass Tool & Supply, Inc. 800-442-0042 (713) 681-4931 [email protected] (713) 682-1889 www.basstool.com
