ADJUSTABLE JAW BORING RINGS For Boring Round & Soft Chuck Jaws ● Quickly bore jaws in a single operation with no plugs or rings ● Suitable for CNC lathes ● Easy to attach - no tools needed ● Jaws are bored at same clamping pressure used to hold part for higher accuracy ● Economical - 3 jaw boring rings cover chucks sizes from 5” - 12” DIRECTIONS 1) Set jaws to correct position 2) Adjust jaw boring ring to fit bolt holes 3) Lock the chuck to clamp jaw boring ring 4) Machine desired size 5) Unlock chuck and remove jaw boring ring CNC LATHE GAGE PART#: 1-USS- EDGE-13000 Used to set lathe tools on the spindle axis for optimum cutting conditions. It can be used to set tools on the spindle axis and eliminate the nub left after cutting. Designed with a large amount of angular adjustability, allowing it to be used with any slant bed or Swiss style CNC lathe. Two different contact faces allows it to work with both upward and downward facing cutting tools. ● Set turning, boring, and facing tools on spindle axis for optimum cutting conditions ● Eliminate the “nub” left by poorly set tools. ● Precision glass vial level with 30’/2mm sensitivity ● Angular adjustability of +/- 60° ● Ground steel shaft supported by dual ball bearings ● Made from high strength aluminum 6-JAW SETRITE™ CHUCKS BORING STARS ● Save set-up time ● Obtain any diameter easily and quickly ● Reduces soft jaw costs ● Allows straight through boring of soft jaws JAW BORING TOOLS JAW BORING RINGS For Boring Round & Soft Chuck Jaws No need to look all over the shop for a setup piece and waste time. Our jaw boring ring is essential for boring soft jaws and round jaws. ● Ideal for machining soft jaws ● Attaches quickly without tools ● Applies equal pressure on all jaws ● Attaches to front of jaws, compensating for “jaw lift” ● Since no discs or bungs are used to clamp jaws, through boring of jaws is possible Jaw Boring Ring (comes complete with 3 pin assemblies) CHUCK DIA ID INCH OD INCH PIN DEPTH PIN DIA PART # 1-USS- 4” 1.335 4.500 0.350” 0.510” JBR-04 5” 2.335 5.500 0.350” 0.510” JBR-05 6" 3.250 6.825 0.350" 0.512" JBR-06 8" 3.500 8.450 0.350" 0.562" JBR-08 10" 5.900 10.150 0.350" 0.709" JBR-10 12" 7.475 12.075 0.400" 0.709" JBR-12 15” 8.900 15.230 0.600" 0.938" JBR-15 Extra Pin Assemblies PIN DEPTH INCH PIN DIA. INCH INDIV. PINS P/N: 1-USS- PIN SETS (3) PART # 1-USS- 0.350" 0.510” JBR-PIN-04 JBR-PIN-04-SET3 0.350" 0.510” JBR-PIN-05 JBR-PIN-05-SET3 0.350" 0.512" JBR-PIN-06 JBR-PIN-06-SET3 0.350" 0.562" JBR-PIN-08 JBR-PIN-08-SET3 0.350" 0.709" JBR-PIN-10 JBR-PIN-10-SET3 0.400" 0.709" JBR-PIN-12 JBR-PIN-12-SET3 0.600" 0.938" JBR-PIN-15 JBR-PIN-15-SET3 How to install: 1. Place the jaw boring ring over your chuck and locate the boring ring pins in the counterbore of your chuck jaws. 2. Turn the jaw boring ring until snug. 3. Activate your jaws. The jaw boring ring will apply equal pressure on all jaws, allowing for a consistent bore. SETRITE - ADJUSTABLE SELF-CENTERING UNIVERSAL CHUCKS STEEL BODY PREMIUM LOW COST .0005” T.I.R. SETRITE™ FEATURES ● Adjusting jaws allow .0005” TIR repeatability on duplicate parts. ● Hardened jaws with ground teeth for precision general chucking. ● Pinions - Hardened nickel steel (1-6, 8, 10, 12”) (3-15”) chucks. ● Scrolls - Hardened nickel chrome Molybdenum alloy steel. ● Two-piece American Standard Tongue and Groove Jaws on 3-jaw and 6-jaw models. ● 4 Adjusting screws -6”, 8”, 10”, 12” ● 8 Adjusting screws - 15” 3-JAW EASY-SET™ CHUCKS 6-JAW EASY-SET™ CHUCKS EASY-SET™ FEATURES ● One year warranty. ● .0005” TIR repeatability on duplicate parts. ● 4 adjusting screws ● Hardened scroll. ● Hardened pinion ● Two-piece tongue and groove jaws. ● Semi-steel body. FOR D STYLE MOUNTING PLATES FOR SETRITE™ & EASY-SET™ CHUCKS FOR A STYLE BLANK ADAPTERS FOR L STYLE THREADED ADAPTERS HARDINGE & ELGIN ADAPTERS 3-JAW SETRITE™ CHUCKS BENEFITS ● Double to triple the clamping pressure of conventional greases ● Provides boundary lubrication protection ● Highly resistant to centrifugal force ● Reduces friction and wear APPLICATION METHODS ● Hand grease guns ● Pneumatic grease equipment ● CHUCK-EEZ may also be applied down to -20° F using a brush with stiff bristles or by burnishing in with a clean cloth. USING CHUCK-EEZ Grease each chuck twice for every eight-hour shift, especially if a lot of coolant is used. Two shots of CHUCK-EEZ is enough since the guideways cannot hold much grease. NOTE: The 16oz cartridge will fit into standard grease guns CHUCK-EEZ is a heavy-duty boundary lubricant designed to increase the clamping pressure of Power Chucks. CHUCK-EEZ is formulated (with a high percentage of molybdenum disulfide) to reduce seizing, galling, fretting wear and to prevent reduced friction under conditions of extreme pressure. It is able to withstand pressures up to 500,000 pounds per square inch. And the tacky nature of the product gives it high resistance to centrifugal force. Rust and oxidation inhibitors are incorporated to maximize rust protection during the life of the lubricant. * Eccentric adjustment of chuck on adapter to obtain required TIR on the workpiece may result in unacceptable vibration at these speeds. Reduce RPM’s accordingly. ● Reduces fretting wear ● Keeps work piece clamped in place ● Assists in wear-in of new chucks ● Lowers maintenance cost CONTAINER SIZE PART # 16 oz. Cartridge 7-950-21478 POWER CHUCKS CALL WITH YOUR SPECIFICATION FOR THE PERFECT SOLUTION 3H-2/3H-2A THRU HOLE 3 JAW LARGE THRU-HOLE POWER CHUCK 3H/3H-A THRU HOLE 3 JAW THRU-HOLE POWER CHUCK 3L/3L-A THRU HOLE 3 JAW EXTRA LONG JAW STROKE POWER CHUCK DIA. THRU HOLE NET WT. MAX* RPM PART # 1-PRA- 5 1.30 15 2600 0516400 6 1.81 27 2500 0626300 8 2.25 49 2200 0826300 10 3.00 76 1900 1026300 12 4.06 116 1500 1226300 15 4.56 205 1300 1526300 DESCRIPTION PART # 1-USS- Jaw Boring Stars-Set of 4 JBT-100 CHUCK SIZE ID OD JAW STROKE MAX RPM PART # 1-USS- 5,6,8” 3.94 6.70 7.40 800 JBR-TL5-8 6,8,10” 4.92 7.90 7.40 700 JBR-TL6-10 8,10,12” 6.30 9.80 8.50 600 JBR-TL8-12 DIA. THRU HOLE NET WT. MAX* RPM PART # 1-PRA- 6 1.540 20 3000 EZ63 8 2.275 43 2800 EZ83 10 2.860 67 2500 EZ103 12 3.285 104 2000 EZ123 15 4.250 141 1800 EZ153 DIA. THRU HOLE NET WT. MAX* RPM PART # 1-PRA- 6 1.540 22 2500 EZ66 8 2.275 47 2200 EZ86 10 2.860 70 2000 EZ106 12 3.285 108 1500 EZ126 15 4.250 240 1300 EZ156 DIA. THRU HOLE NET WT. MAX* RPM PART # 1-PRA- 5 1.30 14 5000 0515400 6 1.81 26 4900 0625300 8 2.25 46 4200 0825300 10 3.00 71 3300 1025300 12 4.06 112 2300 1225300 15 4.56 146 2000 1525300 DIA. TAPER PART # 1-PRA- 6 D-3 0605020 6 D-4 0605021 6 D-5 0605022 8 D-3 0805020 8 D-4 0805021 8 D-5 0805022 8 D-6 0805023 10 D-4 1005021 10 D-5 1005022 10 D-6 1005023 10 D-8 1005024 12 D-6 1205023 12 D-8 1205024 12 D-11 1205025 15 D-6 1505023 15 D-8 1505024 15 D-11 1505025 DIA. TAPER PART # 1-PRA- 6 A-4 0605009 6 A-5 0605010 8 A-5 0805010 8 A-6 0805011 10 A-6 1005011 10 A-8 1005012 12 A-6 1205011 12 A-8 1205012 15 A-8 1505012 15 A-11 1505013 DIA. PART # 1-PRA- 6 0605040 8 0805040 10 1005040 12 1205040 DIA. TAPER PART # 1-PRA- 6 L-00 0605031 6 L-0 0605032 8 L-00 0805031 8 L-0 0805032 8 L-1 0805033 10 L-00 1005031 10 L-0 1005032 10 L-1 1005033 10 L-2 1005034 12 L-0 1205032 12 L-1 1205033 12 L-2 1205034 15 L-1 1505033 15 L-2 1505034 15 L-3 1505035 DIA. TAPER PART # 1-PRA- 6 1.1/2-8 0605041 6 1.3/4-8 0605042 6 2.1/4-8 0605043 8 2.1/4-8 0805043 8 2.3/8-6 0805046 DIA. TAPER PART # 1-PRA- 6 4” TAPER 0605044 6 2.3/16-10 0605045 - 1838 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042
