DISPENSERS FOR MAXIMUM TOOL STORAGE “The Original” Tap Dispenser Dimensions: All models measure 14.5/8”W x 7.3/8”D x 7.3/4”H Weight: 10.1/2 lbs. Small Drawer: 12”W x 7.3/16”D x 1”H Large Drawer: 12”W x 7.3/16”D x 2.1/4”H ● New, one piece drawer slide for long, useful life. ● Stackable. Holds full packages (minimum) of each size. Shown below are the 3 models of tap dispensers stacked on top of each other. Three models shown are: EDP#13500 EDP#13550 EDP#13575 Model 13500 EDP #13500 1/4”-20NC 1/4”-28NF 5/16”-18NC 5/16”-24NF 3/8”-16NC 3/8”-24NF 7/16”-14NC 7/16”-20NF 1/2”-13NC 1/2”-20NF 9/16”-12NC 9/16”-18NF 7/8”-9NC 7/8”-14NF 1”-8NC 1”-14NF Weight: 10.1/2 lbs. Model 13550 EDP #13550 Each size holds taper, plug, bottoming, and spiral point taps. 60 compartments. Holds machine screw sizes: 2-56 3-48 3-56 4-40 4-48 5-40 5-44 6-32 6-40 8-32 8-36 10-24 10-32 12-24 12-28 Weight: 13lbs. Model 13575 EDP #13575 Holds 29 popular metric sizes: 3mm x .50 3mm x .60 4mm x .70 4mm x .75 5mm x .80 5mm x .90 6mm x 1.00 6.3mm x 1.00 7mm x 1.00 8mm x 1.00 8mm x 1.25 9mm x .75 9mm x 1.00 9mm x 1.25 10mm x 1.00 10mm x 1.25 10mm x 1.50 11mm x 1.50 12mm x 1.25 12mm x 1.50 12mm x 1.75 14mm x 1.25 14mm x 1.50 14mm x 2.00 16mm x 1.50 16mm x 2.00 18mm x 2.50 20mm x 2.50 24mm x 3.00 Reamer Cabinets ● 4 models for reamer organization. ● Ideal where compact space is a must. ● Decimal equivalents also listed. Model 13410 EDP #13410 Fractional Reamers 1/16” to 1/2” by 64ths, Weighs 13 lbs.-4 drawers Model 13415 EDP #13415 A to Z Reamers Weighs 13 lbs.- 3 drawers Model 13420 EDP #13420 Wire gauge sizes #1 to #60, Weighs 14 lbs.- 5 drawers Model 13430 EDP #13430 Combination cabinet for over/under and dowel pin sizes, Weighs 11 lbs.- 3 drawers. Dimensions: All 4 models measure 14.5/8”W x 7.3/8”D x 7.3/4”H End Mill Dispensers Dimensions: All models 26”W x 12”D x 9.1/2”H. Each drawer measures 23.1/8”W x 11”D x 2”H. Weight: 36 lbs. Each. INCH Model 13300 EDP #13300 For 2-Flute End Mills. Holds popular sizes 1/16” to 1”. Lockable. Stackable. Model 13325 EDP #13325 For 4-Flute End Mills. Holds popular sizes 1/16” to 1”. Lockable. Stackable. Top Drawer 41 Compartments Holds 6 each single end fractional end mills in following sizes: 1/8”, 3/16”, 1/4”, 5/16”, 3/8”, 7/16” and 1/2”. 3 each 5/8”, 3/4”, 7/8” and 1” with 6 extra compartments for specials. Middle Drawer 41 Compartments Holds 6 each double end fractional end mills in following sizes: 1/16”, 3/32”, 1/8” with 3/16” shank, 1/8” with 3/8” shank, 5/32”, 3/16” with 3/16” shank, 3/16” with 3/8” shank, 1/4”, 5/16”, 3/8”, 7/16” and 1/2”.3 each 5/8”, 3/4”, 7/8” and 1”. Lower Drawer Undivided Use for extra end mills, cutters, drills, reamers and miscellaneous tools. Optional Drawer Divider kit #14030 Carbide Burr Dispenser Dimensions: 14.5/8”W x 7.3/8”D x 7.3/4”H Weight: 10.1/2 lbs. Dimensions: 26”W x 12”D x 9.5/16”H Weight: 38 lbs. Holds sizes: SA-1, SC-1, SD-1, SE-1, SF-1, SG-1, SL-1, SM-3, SA-3, SC-3, SD-3, SE-3, SF-3, SG-3, SL-3, SM-4, SA-5, SC-5, SD-5, SE-5, SF-5, SG-5, SL-4, SM-5 Separates and protects valuable carbide burrs. All steel cabinet with extruded vinyl compartments allow easy and safe storage of carbide burrs. Storing carbide burrs in plastic tubes or sleeve web increases storage capacity of each compartment. Easy to read identification numbers. Master Tap Dispenser Dimensions: 26”W x 12”D x 12.1/2”H Weight: 46 lbs. Model 13585 EDP #13585 ● Holds most common NC/NF sizes from 1/4” to 1.1/2”. ● Holds metrics from 2.5mm to 30 mm. ● Holds machine screw size 2-56 thru 12-28, taper, plug, bottom and spiral. ● Extruded vinyl drawer dividers protect taps. ● Top drawer has 40 compartments ● Second drawer has 78 compartments ● Third drawer has 21 compartments ● Fourth drawer has 13 compartments ● Stackable for larger inventories ● Lockable. Metric Model 13375 EDP #13375 Separates and identifies metric end mills from 2.0mm to 25.0mm. 68 pre-labeled compartments help you quickly locate and use the proper cutting tool. Holds the following metric end mills: 2.0mm, 2.5mm, 3.0mm, 3.5mm, 4.0mm, 4.5mm, 5.0mm, 5.5mm, 6.0mm, 7.0mm, 8.0mm, 9.0mm, 10.0mm, 11.0mm, 12.0mm, 12.5mm, 13.0mm, 14.0mm, 15.0mm, 16.0mm, 17.0mm, 18.0mm, 19.0mm, 20.0mm, 21.0mm, 22.0mm, 23.0mm, 24.0mm, 25.0mm. End Mill Dispenser For Small Inventories Dimensions: 14.5/8”W x 7.3/8”D x 7.3/4”H Weight: 10.1/4 lbs. 1 Compartment for 9/16”, 11/16”, 7/8” 2 Compartments for 3/16”, 5/16”, 7/16”, 5/8”, 1” 3 Compartments for 1/8”, 1/4”, 3/8”, 3/4” 4 Compartments for 1/2” Model 13580 EDP #13580 ● For sizes 1/4”-20 to 1”-14 taps ● Many compartments hold multiples of a given size tap ● Holds bottom, plug and taper of each size: 1/4”-20 1/4”-28 5/16”-18 5/16-24 3/8”-16 3/8”-24 7/16”-14 7/16”-20 1/2”-13 1/2”-20 9/16”-12 9/16”-18 5/8” 11 5/8”-18 3/4”-10 3/4”-16 7/8”-9 7/8”-14 1”-8 1”-14 ● Holds taper, plug, bottom and spiral: 2-56 3-48 3-56 4-40 4-48 5-40 5-44 6-32 6-40 8-32 8-36 10-24 10-32 12-24 12-28 Master Reamer Cabinets Model 196 EDP #13400 ● Lockable, Stackable. ● Stores following reamers: 1/8”-4 ea., .1230 d/p, .1240 under, .1247 d/p, .1260 over, 3 ea. 3/16”, .1855 d/p, .1865 under, .1870 d/p, .1885 over, 3 ea. 1/4”- 4 ea., .2480 d/p, .2490 under, .2495 d/p, .2510 over, 3 ea. 5/16”- 3ea., .3105 d/p- 3 ea., .3115 under- 2 ea., .3120 d/p- 2 ea., .3135 over- 2 ea. 3/8”- 4 ea., .3730 d/p, .3740 under, .3745 d/p, .3760 over, 3 ea. 7/16”, .4355 d/p, .4365 under, .4370 d/p, .4385 over, 2 ea. 1/2”- 4 ea., .4980 d/p- 2 ea., .4990 under, .4995 d/p, .5010 over, 3 ea. Reamer Cabinets shown are stacked on top of each other Shown EDP #13400 Model 13450 EDP #13450 Fractional Reamers 1/16” to 1/2” Over/Under Reamers from .1240 to .5010 Dowel Pin Reamers from .1230 to .4995 Metric Reamers from 1.0mm to 13.0mm x .5 Dimensions: 26”W x 12”D x 12.1/2”H Weight: 43 lbs. FOR TAP SIZES P/N: 1-030 1/4-20 to 1”-14 13500 2-56 to 12-28 13550 3mm to 24mm 13575 FOR TAP SIZES PART # 1-030 #2-#12, 1/4-1.1/2, 2.5-30MM 13585 #2-#12, 1/4-1” (T,P,B) 13580 PART # 1-030-13350 FOR END MILLS PART # 1-030 Inch - 2 Flute 13300 Inch - 4 Flute 13325 Metric 13375 FOR SIZES P/N: 1-030 1/16 to 1/2 x 64th 13410 A to Z 13415 #1 - #60 13420 Over-Under (.124-.501) & 13430 Dowel Pins (.123 - .4995) PART # 1-030-13200 FOR REAMERS P/N: 1-030 1/16-1/2, Dowel Pin, O/U 13400 S/A #13400 plus Metric 13450 - 1775 - Toll Free Fax Email Houston Bass Tool & Supply, Inc. 800-442-0042 (713) 681-4931
[email protected] (713) 682-1889 www.basstool.com
