GASKETING Ultra Blue® RTV Silicone Gasket Maker Fills gaps up to 0.25” when fully cured. Sensor-safe, low odor, noncorrosive. Outstanding oil resistance and joint movement values. Eight times more flexible than cork/composite gaskets; three times more oil resistant than conventional silicones. Temperature range -75°F to 500°F (-59°C to 260°C) intermittent; resists shop and auto fluids and vibration. Suggested Applications: Pump housings, machine tools, compressors, gearboxes, valve covers, oil pans, transmission pans. Fixmaster® EPOXIES Fixmaster® Steel Liquid Steel filled. Pourable and self-leveling. Epoxy is recommended for casting into hard-to-reach areas, anchoring and leveling, and forming molds and fixtures. Permatex® Form-A-Gasket® No. 1 Sealant Reliable paste-like gasket sealant/dressing/coating. Form-A- Gasket #1 sets quickly to a hard set and is recommended for rigid, permanent assemblies. Use to 400°F (204°C). Resistant to gasoline and other solvents. Conforms to MIL-S-45180 D. FORM-A-GASKET® GASKET SEALANTS Permatex® Form-A-Gasket® No. 2 Sealant Reliable paste-like gasket sealant/dressing/coating. Form-A- Gasket #2 sets more slowly to a pliable film best suited for non-rigid, vibrating assemblies. Use to 400°F (204°C). Resistant to gasoline and other solvents. Conforms to MIL-S-45180 D. Fixmaster® Metal Magic Steel™ Steel epoxy in stick form. Cut off a section, knead and apply to leaking pipes or damaged equipment. Cures in 10 minutes. NSF approved, standard 61. 4 oz. stick Underwater Repair Epoxy This putty-like material is ideal for plumbing, irrigation and marine applications because it is unaffected by chlorinated or salt water. It is hand kneadable and fully cures in 1 hour. 4 oz. stick Fixmaster® Aluminum Putty Aluminum-filled epoxy rebuilds and repairs aluminum equipment, forming a non-rusting finish. Clover petroleum Grease Mix is the most widely used. It retains its texture and lubrication properties during extended lapping and leaves a rust preventing film on lapped surfaces. Silicon Carbide is the favorite abrasive for fast cutting of all but the hardest and toughest metals. Hard, sharp crystals break down in grinding and lapping operations to give more sharp edges for continued cutting. Silicon Carbide will produce a smooth flat surface but generally not a polished one. Permatex® Aviation Form- A-Gasket® No. 3 Sealant Nonhardening liquid gasket sealant/dressing/coating is a thin, brushable dressing or sealer for close-fitting parts. Suitable for continuous temperatures to 400°F (204°C). Resistant to antifreeze, aviation fuels, high- detergent oils and lubricants. Conforms to MIL-S-45180 D. Grade and Grit Selector Guide After applying the formula for selecting grit size based upon the micro finish desired, start at the right hand side and read backwards to determine grit size and the corresponding quality grade number. GREASE MIX - SILICON CARBIDE LAPPING COMPOUND Mobilux® EP 1 Brown, Lithium, Extreme Pressure Grease Application: Centralized Lubrication Systems, Other Applications Where Low Temperature Performance is Required Grease Thickener: Lithium Operating Temp: -20°F to 120°F Timken OK Load: 40 lb. 13.7 oz. Cartridge SIZE PART # 1-995- PRICE 3.35 oz. tube, carded 81724 SIZE PART # 1-995- PRICE 11 oz. tube, boxed 80003 SIZE PART # 1-995- PRICE 3 oz. tube, carded 80016 11 oz. tube, boxed 80011 SIZE PART # 1-995- PRICE 4 oz. bottle 80019 16oz. bottle 80017 GRADE GRIT 1 lb Can 1-442 PRICE 7A 1200 515B 5A 800 517 4A 600 518 2A 400 520 A 280 522 B 240 523 C 220 524 D 180 525 E 120 527 F 100 528 G 80 529 USE THESE GRADES FOR Ave. particle size of Abrasive Grain. APPROX. MICRON FINISH GRIT INCHES MICRONS (.001MM) MICRO-FINE Laboratory lapping Precision lapping 7A 1200 .00012 3 1.5 5A 800 .00038 9 4.5 EXTREMELY FINE Polishing Fitting of parts 4A 600 .00056 14 7.0 2A 400 .00090 23 11.5 VERY FINE Lapping dies and gauges Running in gears 320 .00128 33 16.5 A 280 .00175 44 22.0 MEDIUM FINE Roughing on fine work Cylinder lapping B 240 .00248 63 31.5 C 220 .0026 66 33.0 MEDIUM COARSE Roughing valves D 180 .0034 86 43.0 COARSE Grinding large surfaces Sharpening cutters General sharpening E 120 .0056 142 71.0 F 100 .0068 173 86.5 G 80 .0150 267 133.5 7.93 SIZE PART# 1-888 PRICE 1 LB. 97483 57.48 9.50 3.56 8.01 3.97 14.11 SIZE PART# 1-888 PRICE 4 oz. 98853 15.98 SIZE PART# 1-888 PRICE 4 oz. 82093 14.57 SIZE PART# 1-888 PRICE 1 LB. 97463 68.77 70.59 90.76 50.90 32.18 35.34 35.34 35.34 30.64 35.34 35.35 30.64 SIZE PART# 1-444 PRICE 13.7 oz. Cartridge EP1 4.81 - 1716 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042
