Model #315 For 1 to 10 sumps to 400 gallons, with heavy oil & moderate solids loading. OIL SEPARATORS & FILTERS TRAMP OIL SEPARATORS How to Select and Order the Portable Keller Separator for Your Application A Keller portable separator is used to clean several sumps in sequence. We recommend that each sump be cleaned at least once per week. Example: a Model #315 cleans a 100 gallon sump with heavy oil loading in 4 hours, or two sumps per day and 10 sumps per week. Selection charts: Replacement Polypropylene Filter Bags Installation Requirements: Air Flow Air Pressure Air Fitting * 25 micron bags supplied unless otherwise specified. Also available: 50, 10, 5 micron KELLER TRAMP OIL-SKIMMERS TKO-6 mounted to machine tool with CLO-1 magnetic frame. About 0.5 scfm 20 psig to 100 psig 1/4” NPTF Model TKO-10. Footprint (all models) - 14” x 14”. How the TKO Pump/Skimmer works: The self-priming air operated pump pulls the tramp oil/coolant mixture from the surface of the sump through the floating inlet device, then through a cartridge filter which removes any chips from the fluid. The oil/coolant mixture is then pumped through the patented Keller all-plastic separator element immersed in a separator tank. The cleaned coolant continuously returns to the sump. The oil layer collects on the top of the separator tank and is occasionally drained into a waste oil container, simply by opening the oil drain valve. No other operator attention is required. KELLER PORTABLE PUMP/FILTER UNIT ● Increase Tool Life ● Improve Parts Finish ● Eliminate Odor ● Multiply Coolant Life ● Aerate, Recirculate Coolant Model # 457 For 1 to 10 sumps to 1000 gallons, with very heavy oil & solids loading. An inlet device draws in oily coolant from the surface of the sump while avoiding the intake of air, which can interfere with splitting of oil from coolant in the separator tank. One inlet device is used in each sump. The 1-KEL-555-07 Floating Inlet Device (7” wide x 10” long), the most frequently used inlet device, automatically compensates for any changes in the level of coolant in the sump. The 1-KEL-555-07 may be used in pit-type sumps with liquid levels as much as 10 feet below floor level. The 1-KEL-555-05 Floating Inlet Device (2” wide x 12” long) is used when only a narrow access space is available; for example, next to a conveyor. The 1-KEL-555-06 Fixed Inlet Device requires only a 3” diameter hole for access to the sump but must be adjusted manually if the sump level changes significantly. Since a Keller portable separator is to be rotated among several machines in sequence, it is most convenient to mount an inlet device permanently in each sump, rather than moving one inlet device from sump to sump. The connection from the inlet device to the separator is a quick connect garden hose fitting. The Keller Pump/Filter Unit PFA-1002 filters sludge and chips from waterbase machine tool coolant or from cutting oil in sumps, without the need to pump out the sumps. With a recirculation rate of 20 gallons per minute, the PFA-1002 completely cleans settled sludge and suspended solids from a typical sump (from 15 gallons to about 250 gallons) in minutes, and then can easily be moved to another sump and set up to run, simply by connecting a 1/4-inch compressed air line. Each PFA-1002 is supplied complete with a rugged, air-operated diaphragm pump, a high capacity bag filter, and all required inlet and outlet hoses, mounted on a compact (30”x 20”) cart. The filter/regulator for compressed air is provided. Five 25 micron filter bags are provided as standard. Other filter bags from 5 microns to 100 microns are available. Ordering Information * 25 micron filter bags supplied unless otherwise specified Other efficiencies available: 100, 50, 10, 5 micron Specifications: Compressed air flow requirement- 5 SCFM Compressed air inlet fitting- 1/4” NPTF Shop compressed air pressure- 20 psig to 100 psig Shipping Weight (Shipped by UPS)- 100 lbs One Inlet Device #555-07 Supplied With Each Unit Filter Chips & Sludge Without Pumping out Sumps ● Extended tool life, improved parts finish ● Smoke and odor eliminated ● Multiplied coolant life = Much less machine downtime, greatly reduced coolant purchase & disposal costs With these exclusive Keller features: ● Patented permanent oil separating (coalescing) element, never needs changing ● Rugged high flow 1/2” air-operated pump provides rapid tramp oil removal, circulates & aerates entire sump ● Compact inlet device can access any sump ● No electricals ● Sets up in minutes - Requires minimal operator attention KELLER Inlet Devices Keller Model No. (Part #: 1-KEL-) 315 365 457 465 Coolant Recirculation Rate (gal/hr) 200 200 240 270 Number of Sumps Treated 1 - 10 1 - 10 1 - 10 1 - 10 Sump Size Ranges (gallons) 40 - 400 40 - 400 60 - 1000 100-2000 Capability for Volume of Tramp Oil High High Very High Very High Capability for Suspended Solids Load Moderate High High High DESCRIPTION PART # 25 Micron filters, Pack of 5 Bags for #315 1-KEL-RAP-25* PART# 1-KEL TKO-6 TKO-10 TKO-14 For Sump Sizes Medium Large Large Tramp Oil Loading Moderate Heavy Very Heavy Oil Rejection Rate of Coolant Efficient Slow Slow SPECIFICATIONS Footprint 14" x 14" (All Models) Height 24" 30" 36" Weight 39 lbs 47 lbs 55 lbs Compressed air requirements 0.5 SCFM @ 20 to 125 psig Electricals None (All Models) ACCESSORY ITEMS (All Models) Replaceable filter element, 150 micron, 10" long 1-KEL-R10-3150 Permanent washable filter element, 100 mciron, 10" long 1-KEL-R10-2130 "Cling-On" frame with magnets, to mount TKO-6 to side of machine tool 1-KEL-CLO-1 DESCRIPTION PART # Pump/Filter Unit, with 5 Filter Bags 1-KEL-PFA-1002* Replacement Filter Bags, Box of 5 Bags 1-KEL-RCP-25* - 1696 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042
