RANGE .0005" RESOLUTION PART# .0001" RESOLUTION PART# 0" - 2.3/8" 1-GM-PD-8000 1-GM-PD-8000-1 0" - 6" 1-GM-PD-8001 1-GM-PD-8001-1 6" - 12" 1-GM-PD-8002 1-GM-PD-8002-1 12" - 16" 1-GM-PD-8004 1-GM-PD-8004-1 16" - 20" 1-GM-PD-8006 1-GM-PD-8006-1 20" - 24" 1-GM-PD-8008 1-GM-PD-8008-1 24" - 28" 1-GM-PD-8010 1-GM-PD-8010-1 28" - 36" 1-GM-PD-8012 1-GM-PD-8012-1 36" - 44" 1-GM-PD-8013 1-GM-PD-8013-1 44" - 52" 1-GM-PD-8014 1-GM-PD-8014-1 52" - 60" 1-GM-PD-8015 1-GM-PD-8015-1 60" - 72" 1-GM-PD-8016 1-GM-PD-8016-1 DESCRIPTION LENGTH P/N: 1-GM Cap - PD-6001-PD4M Indicator Base - Mitutoyo Indicator Only - 4-2-617 Cap and Base Assembly - PD-6001-CBA Adjustment Cap Lock Nut - PD-6001-PD3 Adjustment Cap - PD-6001-PD2 Contact Point Adapter - PD-6001-PD1 Extension Rods for PD-6001 & PD-6002 .430" PD-6001-PDA .860" PD-6001-PDB 1.290" PD-6001-PDC 1.720" PD-6001-PDD 3.440" PD-6001-PDE 5.590" PD-6001-PDF 7.740" PD-6001-PDG 10.320" PD-6001-PDH 12" PD-6001-12E 24" PD-6001-24E 36" PD-6001-36E THREAD PITCH P/N: 1-GM 1 T562C 2 T288C 3 & 3.1/2 T188C 4 T144C 4.1/2 T128C 5 T115C 5.1/2 T105C 6 T096C 8 T072C 10 T057C 11.1/2 & 12 T050C 14 & 16 T041C 18 T032C THREAD PITCH P/N: 1-GM 1 T531TC 1.1/2 T344TC 2 T266TC 2.1/2 T219TC 3 T188TC 3.1/2 T144TC 4 T128TC 5 T105TC 6 & 7 T090TC 8 T062TC 10 T050TC 12 & 14 T041TC 16 T032TC THREAD PITCH P/N: 1-GM 1 T562C 1.1/4 T437C 1.1/2 T375C 2 T281C 2.1/2 T219C 3 T188C 3.1/2 T156C 4 T144C 5 T115C 6 T096C 8 T072C 10 T057C 12 T050C 16 & 18 T032C PITCH (mm) P/N: 1-GM 7 T144C 6 T125C 5 T096C 4 T082C 3.1/2 T072C 3 T062C 2.1/2 T050C 2 T041C 1.1/2 T032C PITCH (mm) P/N: 1-GM 4 T096C 3 & 3.1/2 T072C DESCRIPTION P/N: 1-GM Thread Disk software TDWIN PITCH DIAMETER GAGES ACCURACY ● Eliminates the comparative fit of ring and plug gages. ● Reports the exact size of a thread on the dial indicator ● Allows auditable measurement results ● Provides exact threading offset data to machinists PD-8001 PD-6000 EXTENSION RODS PD-6001 COST SAVINGS ● Eliminates the need to buy multiple gages by adjusting to a range of diameters ● Requires no costly setting masters ● Eliminates unnecessary damage to parts ● Outlasts traditional gages due to minimal thread roll wear EXTERNAL PITCH DIAMETER GAGES (0” to 72” DIAMETERS) FOR STRAIGHT THREADS The ball pitch diameter gages or “GO/NO GO” gages indicate the pitch diameter size of the product’s external thread. The gages are adjustable within a size range and use interchangeable contact points to measure different pitch threads. Setting dimensions for the pitch diameter gages are provided by the TDWIN™ software. Software and contact points are sold separately. Indicators have a 1/2” travel and either .0005" or .0001" resolution. INTERNAL PITCH DIAMETER GAGES (1.1/2” to 27” DIAMETERS) FOR STRAIGHT THREADS ("V" & ACME THREADS) The ball pitch diameter gages or “GO/NOGO” gages indicate the pitch diameter size of the product’s internal threads. The gages are adjustable within a size range and use interchangeable contact points to measure different pitch threads. Setting dimensions for the pitch diameter gages are provided by the TDWIN™ software (sold separately). All of the PD-6000 series are sold without contact points. Indicators have a 1/2" travel and either .0005" or .0001" resolution. REPLACEMENT PARTS FOR PD-6001 & PD-6002 (EXTENSIONS HAVE #10-32 THREADS) SPECIFICATIONS ● Pitch Diameter Gage - Adjustable internal or external gage with indicator that measures a range of pitch diameters. ● Indicators available include Inch (.0001”or .0005”) or Metric (.01mm or .005mm). Refer to the internal and external gage models and sizes below for proper selection. ● Contact Points - Sold separately. Precision ground matched contact point sets for attaching to pitch diameter gages. Inspect UN Series, ACME, and Stub ACME, ISO Metric Series, 7°X45° Buttress, and Whitworth thread forms. Common pitches ranging from 1 TPI - 18 TPI in stock. Special thread forms available upon request. CONTACT POINTS UN SERIES 60° “V” THREADS Two are required for most gages. TRUNCATED CONTACT POINT 7° X 45° BUTTRESS ISO METRIC 60° SERIES T041 T072 T115 T250 T062 T105 T125 ACME OR STUB ACME TRAPEZOIDAL THREAD ● Use ANSI tables, formulas, and tolerances ● Calculates standard and non-standard product thread diameters from #000 to 99.8” THE TDWIN™ THREAD SOFTWARE calculates critical dimensions for threads based on ANSI tables and formulas. Thread types supported by the program include: UN, UNJ and UNR series, Acme, Stub Acme, Stub Acme Modified I and II, Metric M & MJ, 7° X45° Buttress,and General Purpose Pipe Threads. To generate critical dimensions instantly, enter basic thread information on the Thread Type Entry screen, such as: thread type, thread class, nominal diameter, and threads per inch. Once the results are computed, tabs at the bottom of the program allow selection of several types of calculated information, including dimensions and tolerances for product threads, ring gages, set plugs, plug gages or Gagemaker’s Thread Diameter gages. If measuring internal and external shallow taper diameters is a problem, the Ball Mic SET DIM Tool provides setting dimensions for ball micrometers or Gagemaker’s BX-1000 groove gage. The program calculates ball mic settings for any tapered surface geometry. Other features of the program include the ability to print thread dimension reports, providing a paper copy of any calculation. These reports provide the same critical dimensions that display in the program. A multiple calculation window capability is a feature that allows performing several different thread calculations at the same time. The Pitch Diameter Gages include the PD-6000 Series which measures internal pitch diameters from 5/8”-36”, and the PD-8000 Series which measures external pitch diameters ranging from 0”-72”. These gages use interchangeable contact points (sold seperately), which seat in the thread at the pitchline of the part during inspection. The contact points are interchangeable to allow measuring different thread pitches. NOTE: For truncated, replace ‘C’ with ‘TC’ in the Part #. RANGE .0005" RESOLUTION PART# .0001" RESOLUTION PART# 1.1/2" - 9 1-GM-PD-6000 1-GM-PD-6000-1 6" - 24" 1-GM-PD-6001 1-GM-PD-6001-1 9" - 27" 1-GM-PD-6002 --- REPLACEMENT ARMS FOR PD-6000 SERIES LENGTH PART# 2.1/2" 1-GM-PD-6000-02 4.1/2" 1-GM-PD-6000-07 TDWIN™ THREAD SOFTWARE ● Calculates ANSI ring and plug gage dimensions ● Addresses pitches from 1 to 400 ● Calculates Gagemaker style thread gage setting dimensions NOTE: The TDWIN Software is offered as an online download only. 8000 SERIES PARTS & ACCESSORIES DESCRIPTION PART# 11" Long Extension Arm Provides 8" Dia. Adjustment 1-GM-PD-8000-2-11 Lower Arm Replacement, 8" Overall Length 1-GM-PD-8000-2-8 - 572 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042
