MAGNETIC V-BLOCKS ECE-208/ECE-212 ECE-612 “SINE SET” SYSTEM BOLT-ON MAGNETIC CHUCKS All of Suburban’s bolt-on max-C-mag permanent magnetic chucks are perfect SineMate accessories. As part of the SineSet System, these low profile chucks can be used alone as parallel chucks, or with a sine plate or compound sine plate to obtain a magnetic sine plate or magnetic compound sine plate. These chucks can be mounted to sine plates of the same series (SO, S1, or S2) and size in seconds, with little or no indicating, using only four bolts and no clamps. ◄ ECE-612 S1 S1 A B S2 H H1 H2 C 150 ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ ◄ SINE PLATES ● Minute angle step .200” built into the gage block roll eliminates step in base plate. ● Two hardened and ground side rails and one locking strap included. ● Locking strap always remains below the top surface. ● Large hinge pins for extra strength. ● Tapped holes in top plate 6” x 6” or smaller 1/4”-20”, larger models have 3/8”-16” tapped holes. Slotted Angle Plates OPEN END TYPE- 4 faces and all ends machined square and parallel within 0.002” per 6”. WEBBED TYPE- 2 faces and all ends machined square and parallel within 0.002” per 6”. B C A WEBBED ● Made of high quality, stress-relieved, cast iron. B C A OPEN SIZE (INCHES) SLOTS PART # A B C WEBBED OPEN WEBBED 8-519 OPEN 8-520 3.1/2 3 2.1/2 (4) 7/16 N/A 101 4.1/2 3.1/2 3 (4) 9/16 (4) 9/16 102 6 5 4.1/2 (4) 11/16 (7) 9/16 103 7 5.1/2 4.1/2 (4) 11/16 (8) 9/16 104 8 6 5 (4) 9/16 (8) 9/16 105 9 7 6 (4) 11/16 (13) 11/16 106 10 8 6 (4) 11/16 (13) 11/16 107 12 9 8 (11) 11/16 (13) 13/16 108 ANGLE PLATES ● Suburban’s precision angle plates are of solid, one piece construction. ● Made of steel, hardened to Rc 58-62 and ground flat square and parallel within .0002”. ● Tapped holes on all models. ● The AP-664-S1 model is a SineMate 90 degree conversion plate. It’s hole pattern duplicates that of the 6” x 6” SineSet sine plates, allowing the S1 SineMate accessories to be bolted on. AP-444-S1 AP-664-S1 DIMENSIONS INCH TAPPED HOLES WEIGHT LBS. PART# 1-SUB 4 x 3 x 3 x 1 (13) 1/4-20 6 AP-334-S0 4 x 4 x 4 x 1.1/4 (13) 1/4-20 10 AP-444-S1 6 x 4 x 4 x 1.1/4 (14) 3/8-16 13 AP-446-S2 4 x 6 x 6 x 1.1/4 (33) 1/4-20 20 AP-664-S1 HIGH PRECISION VISES Quick Acting - New and Improved ● Suburban’s high precision toolmaker’s vises have bodies of solid, one-piece steel construction. ● The bodies and jaws are hardened to Rc 58-62. ● All of Suburban’s vises are ground flat, square, and parallel within .0002” to .0003”, depending on the size. ● Because of the exacting design of the vises, the jaw is pulled “into” the base at approximately 45 to 60 degrees to the base. This insures maximum holding power with superior hold-down force on the jaw to eliminate tilting and lifting. V-225-S0 V-237-S1 Toolmakers Vises SPECIAL FEATURES: ● All the V-237 Vises have a “ratchet mechanism”, consisting of a “notched” pocket and “solid” drawbar, that eliminates the loose pin in the drawbar assembly. ● The V-237-J and V-237-J-S1 Vises have ground vees in the tops of the jaws and 1/8” x 1/8” steps on the inside faces of the jaws, for even more versatility in holding round or small parts. Two hold-down clamps are included with these 2 models for use in conjunction with these top vees. Large Vises V-411 V-411-S2 V-612 V-612-S2 Stepped Jaw Vises V-237-J DIMENSIONS INCH JAW CAP. JAW HEIGHT PART# 1-SUB 5.7/8 x 2 x 2 3.1/4 1 V-225 5.7/8 x 2 x 2 3.1/4 1 V-225-S0 7.1/2 x 3 x 2.5/8 4.3/4 1.5/16 V-237 7.1/2 x 3 x 2.5/8 4.3/4 1.5/16 V-237-S1 7.1/2 x 3 x 2.5/8 5 1.5/16 V-237-J 7.1/2 x 3 x 2.5/8 5 1.5/16 V-237-JS1 11 x 4 x 3 7 1.7/16 V-411 11 x 4 x 3 7 1.7/16 V-411-S2 12 x 6 x 3.7/16 8 1.11/16 V-612 12 x 6 x 3.7/16 8 1.11/16 V-612-S2 DIMENSIONS L x W x H CENTER DIS. OF ROLLS WEIGHT LBS PART# 1-SUB 6 x 3 x 2 5.000 9 SP-136 4 x 4 x 2 3.000 9 SP-44-S0 6 x 5 x 2.1/4 5.000 17 SP-555 6 x 6 x 2 5.000 18 SP-66-S1 6 x 12 x 2.5/8 5.000 47 SP-612-S2 8 x 12 x 2.5/8 5.000 62 SP-812-S2 12 x 12 x 2.5/8 10.000 90 SP-1212S2 12 x 6 x 2.5/8 10.000 45 SP-126-S2 DIMENSIONS L x W x H SINE SYSTEM WEIGHT LBS PART# 1-SUB FINE POLE - 1/8” Steel x 1/8” Separators 4 x 4 x 2.5/8 0 12 MC-44-FPS0 6 x 6 x 2.5/8 1 25 MC-66-FPS1 6 x 12 x 2.5/8 2 47 MC-612FPS2 6 x 18 x 2.5/8 2 70 MC-618FPS2 8 x 12 x 2.5/8 2 63 MC-812FPS2 12 x 12 x 2.5/8 2 106 MC1212FPS2 12 x 18 x 2.5/8 2 160 MC1218FPS2 12 x 24 x 2.5/8 2 212 MC1224FPS2 Giant Slotted Angle Plates - Webbed B C A Available in machined finish, square and parallel within 0.002” per 6”, or ground finish (up to 20”), square and parallel within 0.0005”per 6”. ● Made of high quality, stress-relieved, fine grained, cast iron. SIZES (INCHES) WEIGHT (lbs) MACHINED 8-519 GROUND 8-520 A B C 16 12 9 112 401 20 16 12 200 402 12 24 18 300 403 18 30 24 700 404 Box Parallels ● Made of high quality, stress-relieved, fine grained, cast iron. ● All faces and ends finished square and parallel. ● Available machined or ground. ● MACHINED FINISH - size ±0.015”, square and parallel within 0.002” per 6”. ● GROUND FINISH - size ±0.002”, square and parallel within 0.0005” per 6”. B C A STYLE SIZE (INCHES) MACHINED 8-519 GROUND 8-520 A B C NO CENTER WEB 4 4 4 301 4 4 6 302 4 6 6 303 5 5 5 304 5 10 10 305 WITH CENTER WEB 6 6 6 306 6 6 8 307 6 12 12 308 8 8 8 309 MAX DIAMETER CAPACITY DIMENSIONS HOLDING POWER LBS. PART# L H B C H1 H2 S1 S2 V-FACE SURFACE 1-EAR- 1.97" 3.15 2.83 2.20 - - - - - 121 154 ECE-208 2.56" 4.53 3.94 2.95 - - - - - 198 242 ECE-212 4.33" 4.65 2.44 2.99 1.97 1.97 0.47 1.89 2.44 242 350 ECE-612 - 1552 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042
