POCKET SCRIBERS Handle made of steel tubing, knurled and nickel plated. Scriber point held firmly in handle by chuck, and when not in use can be reversed, telescoped into handle and locked by a slight turn of chuck. Hexagon head prevents rolling. AUTOMATIC CENTER PUNCHES When handle is pressed down, built-in mechanism strikes blow. Force of blow is regulated by turning knurled cap. Constant spring tension assures uniform depth and size of center marking for each setting of cap. Point removes for regrinding. Punches strike heavier blows in proportion to sizes as listed below. NOTE: Special Points for stamping numbers, letters, special symbols, etc. can be furnished. Please inquire. Packed one in a box. IMPROVED LEVELS MECHANICS’ No. 98 levels have ground and graduated main vials. All levels have cross test vial, except 4 inch size. 12 inch size has in addition a plumb vial, and 18 inch size a double plumb vial. Plumb vials on No. 98-12” and 18” levels are ground. Main vials are adjustable for positive setting and housed in brass tube with friction fit closing cover to prevent breakage. Level bases are seasoned castings with black wrinkle finish, accurately machined and finished on bearing surface. An involute longitudinal groove between bearing flats provides accurate seating on round work. STEEL RULE DEPTH GAGE 0-6"/0-150mm WIGGLER OR CENTER FINDER DOUBLE STEEL SQUARE SET MASTER PRECISION LEVEL 2.1/2” Hardened & Ground Head and Blades SMALL HOLE GAGE SET SMALL HOLE GAGE SET SMALL HOLE GAGE SET No. 829 small hole gages accurately measure holes, slots, grooves and recesses. Split ball contact regulated by turning knob at end of handle. Measurements obtained by measuring over ball contact with micrometer. Contacts hardened for long life. Similar to No. 829 but with flatted contacts for checking size of shallow holes, slots, etc. Knurled knob at end of handle adjusts split contacts to size, and final reading is obtained with micrometer over contacts. Hardened contacts. Short type for measuring in close quarters. Approx. 2” long. ● Blades are adjustable so it can be used in places impossible to use a square with stationary blades. ● A knurled clamping nut with tension spring accurately locks the blades in any desired position. ● Graduations: 32nds & 64ths 5 PCS SUPPLIED IN A CASE. 4 PCS SUPPLIED IN A CASE. Similar to No. 830 but longer length. Flatted contacts for checking size of shallow holes, slots, etc. Knurled knob at end of handle adjusts split contacts to size and final reading is obtained with micrometer over contacts. Contacts hardened. ● Bevel edge has 30°& 45°ends. ● Narrow blade is 5/32” wide and particularly adapted for squaring small holes. Ground and graduated main vial of 10 second accuracy - one division equals .0005” per foot. Auxiliary level vial shows lateral position as guide to horizontal setting. Insulated from handling by non-conductive top plate. Level vials positioned to reduce breakage. Made of seasoned cast iron. Base carefully machined and scraped. Black wrinkled finish on non-working surfaces. Sent in wooden case. PRECISION INSTRUMENTS Starrett No. 706 1-2-3 Blocks with holes are manufactured to precision tolerances. Because of their extreme accuracy, these blocks are a must for all inspection labs and are of great value in shop set-ups such as precise positioning of workpiece on milling machines, jig borers, drill presses and any application where precise positioning is important. Specifications: Blocks are 1X2X3 inches Parallelism: .0001 in. Squareness: .0001in/in. Hardness: R/C 63-65 Flatness: .0001 in. 1” x 2” x 3” BLOCKS MODEL PART# 1-STR DESCRIPTION 70682 57122 Match pair in box. Furnished with offset indicator holder and new chuck design to hold all attachments. Four attachments adapt the tool to countless applications and are snapped in chuck without removing collet nut. Using offset indicator holder D with Starrett Last Word Test Indicators, the mechanic can sweep holes or O.D.’s for checking run-out or concentricity; establish center distances; check straightness or alignment of flat surfaces. With point A, working centers can be accurately located. 237 Steel Rule Depth Gages (0-6" Range) Model Part # Graduation Head Length x Width 237 1-STR-51080 32nds, 64ths 2.5/8 x 1/8" 237M Steel Rule Depth Gages (0-150mm Range) Model Part # Graduation Head Length x Width 237M 1-STR-51081 mm, 1/2mm 66 x 3mm MODEL PART# 1-STR RANGE S829EZ 53074 .125” - .200” MODEL PART# 1-STR DESCRIPTION S828HZ 53064 Center Finder, Complete with Case and 4 Attachments, A, B, C, D S828 53065 Center Finder, without Indicator Holder, without Case 828A 53066 Shank with Point, Length: Closed-2.3/8”, Open-4.1/8”, Shank Dia.-3/8” 828B 53067 Ball Contact Only (.250” ball) 828C 53068 Disc Contact Only (.100” disc) 828D 53069 Offset Indicator Holder Only MODEL S830FZ PART# 1-STR-53081 RANGE .125”-.500” MODEL S831EZ PART# 1-STR- 53087 RANGE .125”-.500” MODEL PART# 1-STR POINT HANDLE DIA. POINT LENGTH 70A 50323 STEEL 1/4” 2.3/8” 70B 50324 STEEL 3/8” 2.7/8” PT02355A 70332 STEEL Point Only for No. 70A PT02355B 70333 STEEL Point Only for No. 70B 70AX 50327 CARBIDE 1/4” 2.3/8” 70BX 56092 CARBIDE 3/8” 2.7/8” PT14398 71527 CARBIDE Point Only for No. 70AX PT19306 72049 CARBIDE Point Only for No. 70BX MODEL PART# 1-STR LENGTH DIAMETER 18AA 50119 4” 7/16” 18A 50120 5” 9/16” 18B 50121 5.1/4” 11/16” 18C 56757 5.1/4” 11/16” PT02947 70380 Point Only for Nos. 18AA, 18A PT02948 70381 Point Only for No. 18B SIZE WITHOUT CASE WITH CASE MODEL PART# 1-STR- MODEL PART# 1-STR- 4” 98-4 50440 — — 6” 98-6 50441 — — 8” 98-8 50442 — — 12” 98-12 50443 98Z-12 50444 18” 98-18 50445 98Z-18 50446 MODEL PART# 14D 1-STR-50118 MODEL PART# 1-STR- LENGTH BASE WIDTH BASE CASE HEIGHT LEVEL 199Z 50719 15” 1.5/8” 3” ● The gage consists of a nicely finished, hardened steel head and an accurate, machine divided, tempered steel rule. ● Gage can be smoothly adjusted to the required measurement and then locked into position by a knurled nut ● Base is cut out on one side, adjacent to the rule, permitting easier readings and more accurate measurements - 1190 - Bass Tool & Supply, Inc. Houston Email Fax Toll Free www.basstool.com (713) 682-1889 [email protected] (713) 681-4931 800-442-0042